Materials Testing CS2 - W D Turner Company

Model	ozf	gf	lbf	kgf	N
CLC-250G	8 x 0.002	250 x 0.05	0.5 x 0.0001	0.25 x 0.0001	2.5 x 0.0005
CLC-0002	32 x 0.005	1000 x 0.1	2 x 000.2	1 x 0.0001	10 x 0.001
CLC-04-5	72 x 0.01	2000 x 0.2	4.5 x 0.0005	2 x 0.0002	20 x 0.002
CLC-0010	160 x0.02	5000 x 0.5	10 x 0.001	5 x 0.0005	50 x 0.005
CLC-0020	320 x 0.05	10,000 x 1	20 x 0.002	10 x 0.001	100 x 0.01
CLC-0050	800 x 0.1	25,000 x 2	50 x 0.005	25 x 0.002	250 x 0.02
CLC-0100	1600 x 0.2	50,000 x 5	100 x 0.01	50 x 0.005	500 x 0.05
CLC-0200	3200 x 0.5	100,000 x 10	200 x 0.02	100 x 0.01	1000 x 0.1
CLC-0500	8000 x 1	250,000 x 20	500 x0.05	250 x 0.02	2500 x 0.2
CLC-1000	16000 x 2	500,000 x 50	1000 x 0.1	500 x 0.05	5000 x 0.5

The rear of the crosshead is attached to a vertical linear rail assembly that accurately defines

the crosshead alignment. This system ensures minimal sideways movement of the crosshead

together with minimal vertical "rocking" of the crosshead under all loading conditions.

CS machines are bench mounted, microprocessor controlled, single column loading

frames. The high stiffness frame incorporates a crosshead guidance system to prevent side

loading of the sample under test. The crosshead is driven by single leadscrew, motor and DC

pulse width modulated system to achieve a wide speed range over the full load range.

These machines are capable of running full load at full speed

The Dell Tablet Keyboard folds conveniently to the back, allowing access of the touch screen surface for operation. The tablet can also be used in conventional fashion by not using the mounting bracket but placing the Tablet next to the machine.

Model	Speed Range	Maximum Travel	Maximum Force
CS2-225	0.01-1270 mm/min (0.001-50 in/min)	500mm (19.7 in)	1000N (225 lbf)
CS2-1100	0.01-1016 mm/min (0.001-40 in/min)	800 mm (31.5 in)	5000N (1124 lbf)

Load cells are easily changed for light duty testing. Electronics in the load cell connectors retain the Load Cell information (size, calibration points & serial number) along with history of overloads. To change, turn off power to the machine. Next, simply disconnect the Load Cell's electrical connection and loosen a single bolt to remove. Install another load cell in it's place (electrical connector and bolt connection is the same for all load cells).

Load cells for lower range testing are recommended according to need. The following table shows available load cell sizes for the CS series machines. Note, we recommend keeping back up load cells in case one is accidently damaged or overloaded.

The CS machine is ideal for limited budgets where materials testing is still required, especially in production testing. The machine comes equipped with a Dell Tablet loaded with Windows 10 Professional. The software is already loaded on the tablet.

Use the Dell Tablet as a Console

on the Machine Column...

Or flip open to access a keyboard

(set on table next to machine).

The touch screen can also be used.